Soldering Tip Cleaning Ball

1 Channel Relay Module DC 5V 10A Low/High Trigger for Arduino features:
- Channel: 1 (protected with Optocoupler)
- Supply voltage: 5V
- Output Current: 10A
- Relay activation current: 15mA ~ 20mA
- Insulation: Yes
- Trigger signal type jumper (low / high)
- LED indicator
- Dimensions: 30x 54mm
- Has a jumper that allows to choose type of trigger signal (low / high)
- This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL)

Momentary Switch Push Button Black N/O 7mm features:
- Momentary pushbutton N/O (normally open)
- Black button
- Dimensions approx. 7 mm x 27 mm
- Recessed with nut and washer
- Load current (supported): 1A to 230V / 2A to 125V
- Drill to embed: 7 mm +/- 0.2
- Operating temperature: -55ºC to + 85ºC

TP4056 Module Lithium Battery Charger with Protection features:
- TP4056 Li-Ion Micro USB Charger
- Upgraded version of previous TP4056
- Micro USB connection to charge directly from the PC
- Ideal for 18650 batteries
- Based on the TC4056A regulator
- Input Voltage: 4.5V - 5.5V DC
- Full charge voltage: 4.2V +/- 1.5%
- Max Output Current: 1A
- Overvoltage protection 4.2V
- Over discharge protection 2.4V
- LED indicator: charging blue, charging red
- Operating temperature: -10ºC to + 85ºC
- IN + and IN- connection for electronic circuits
- Overcurrent protection: 3A
- Measurements 26 x 19 x 5 mm
- Possibility of current change through Rprog

Welding Wire 100g Tin 60/40 Sn/Pb Lead 2.5% Flux 1.5mm features:
- 100gr. 1.5mm diameter welding wire. 60% tin and 40% lead
- Fusing temperature 183 „ƒ / 190 „ƒ
- Alloy Sn60 Pb40
- Flux 2.5%
- Quantity: 1 unit

Blue 2 pole PCB mount screw terminal 5.08mm pitch Printed Circuit Board Terminal 3 poles 5.08mm pitch features:
Number of Contacts: 3
Pitch: 5.08mm
Number of Rows: 1
Mounting Type: PCB
Gender: Male
Allowable Section: 1.5mm2 (22- 14 AWG)
Termination method: screw
Type: screw terminal block
Nominal current: 16A
Nominal voltage: 250V
Color: blue
Material: Nylon 66
Depth: 10mm
Width: 7.5mm
Length: 10mm

A high-performance regulator-booster.
24V battery charger - DC / CV method.
Power supply of the laptop from a 12V car battery.
A high-performance dimmer-regulator.
Charger for Li-Ion, Li-Po batteries etc. - CC / CV method.
LED Constant current driver for LED diodes.
Characteristic:
- Input voltage: 6V -40V
- Output voltage: 1.25-35V (adjustable)
- Output current: 8A, (10A maximum)
- Output power: 300W maximum
- Efficiency of Conversion: up to 95%
- Wiring: Solderless terminal
- Operating frequency: 300kHz
- Ambient temperature exceeds 40 ° C, increase heat dissipation
- LED indicator two-color;
- Charge red
- Fully charged light green
- No charge green

2x Insulation Tapes PVC Yellow 10m x 15mm x 0.13mm features:
- PVC insulating tape with adhesive
- Thickness of 0.13 mm
- Measures 10m x 15mm
- Quantity: 2 units
- Heat resistance: 80°C

Mini ESP8266 ESP12E CH340 WiFi Development
NodeMcu module based on ESP8266 controller and programming in Lua language
NodeMcu it is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC
It works as a standard WiFi 802.11 b / g / n 2.4 GHz
Wemos D1 Mini ESP8266 ESP12E CH340 WiFi Wireless Development features:

- Compatible with Arduino, programming with the Arduino IDE
- Power supply voltage: 5V
- LOGICAL LEVELS: 3.3V
- 11 input / output pins
- 1 ADC (input: 0-3.3V)
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz - Band: 2400 (MHz)
- Wi-Fi Direct (P2p), Soft Access Point
- Integrated TCP / IP stack
- PLL, regulators and power management units Integrated