WIFI modules

The SparkFun WiFi ESP8266 Shield is a shield for Arduino R3 R3 board enabling internet connection. ESP8266 as you all know is a solid fundament for any IoT project an in this version it can be simply and easily put on your board. It is a great middle ground between the sole module and the development board such NodeMcu or WeMos. So if you need a relatively cheap and super reliable way to internet for your Arduino project - this is the shield for you! ESP8266 shield WiFi comes with an AT-command firmware, hence can be controlled by any UART. It works great with any Arduino R· layout. The shield doesn´t have the headers on.

ESP8266 Thing Dev board from Sparkfun is a reliable, strong solution for IoT projects. The ESP8266 is a well-known WiFi controller from the boards such as NodeMcu and or WeMos. This board increases the reliability to maximum though. This version comes without headers.

ESP8266 Thing Dev board from Sparkfun is a reliable, strong solution for IoT projects. The ESP8266 is a well-known WiFi controller from the boards such as NodeMcu and or WeMos. This board increases the reliability to maximum though. This version comes with headers.

The SparkFun ESP32 thing is an upgrade to boards based on the popular ESP8266. What the 32 version has to offer on top? Well one of the largest upgrades is support for Bluetooth communications and nearly 30 I/O pins. Makes it pretty perfect for any IoT solution, right?

SparkFun XBee Explorer Dongle enables the communication between your computer and any XBee device, as in case of any XBee device, without any cables!

The module is compatible with Series 1, Series 2.5 and standard Pro version with voltage regulator functioning with the current up to 500 mA.

SparkFun XBee Explorer Dongle enables the communication between your computer and any XBee device, as in case of any XBee device, without any cables!

The module is compatible with Series 1, Series 2.5 and standard Pro version with voltage regulator functioning with the current up to 500 mA.

WIFI transceiver based on the ESP8266 controller.
It has a microcontroller and 2 GPIO pins to be able to operate autonomously without the need for an external microcontroller. Characteristic: - Voltage of power: 3.3V
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz
- Band: 2400 (MHz)
- Wi-Fi Direct (P2p), Soft Access Point
- Integrated TCP / IP stack
- PLL, regulators and integrated power management units
- Output power: 0.15 (W); + 19.5dBm in 802.11b mode
- Consumption in low power mode:

- WIFI module based on the ESP8266 controller
- ESP8266-12F is an improved version of ESP8266-12E
- It works as a standard WiFi 802.11 b / g / n 2.4 GHz. It is equipped with 22 outputs (pitch 2 mm) of which 11 are GPIO, ADC 1 and SPI. A LED and a PCB antenna have been incorporated
ESP-12F ESP8266 12F WiFi Board Module features:
- Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz
- Band: 2400 (MHz)
- Wi-Fi Direct (P2p), Soft Access Point
- Integrated TCP / IP Stack.
- PLL, regulators and integrated energy management units
- Output power: 0.15 (W); + 19.5dBm in 802.11b mode
- Consumption in low energy mode: <10 uA
- Integrated 32-bit processor

NodeMcu module based on ESP8266 controller and programming in Lua language.
NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC.
ESP8266-12E is an improved version of ESP8266-12.
It works as a standard WiFi 802.11 b / g / n 2.4 GHz.
USB communication - the CH340 chip. Characteristics of ESP 12E:
- Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz
- Band: 2400 (MHz)
- Wi-Fi Direct (P2p), Soft Access Point
- TCP Stack / Integrated IP
- PLLs, Regulators and Integrated Power Management Units
- Output Power: 0.15 (W); + 19.5dBm in 802.11b mode

NodeMcu module based on ESP8266 controller and programming in Lua language
NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC
ESP8266-12E is an improved version of ESP8266-12
It works as a standard WiFi 802.11 b / g / n 2.4 GHz
USB Communication - CP2102 Chip
Characteristic:
ESP 12E ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi features:

- Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz
- Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point
- Integrated TCP / IP stack
- PLL, regulators and integrated power management units
- Output power: 0 , 15 (W); + 19.5dBm in 802.11b mode

Mini ESP8266 ESP12E CH340 WiFi Development
NodeMcu module based on ESP8266 controller and programming in Lua language
NodeMcu it is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC
It works as a standard WiFi 802.11 b / g / n 2.4 GHz
Wemos D1 Mini ESP8266 ESP12E CH340 WiFi Wireless Development features:

- Compatible with Arduino, programming with the Arduino IDE
- Power supply voltage: 5V
- LOGICAL LEVELS: 3.3V
- 11 input / output pins
- 1 ADC (input: 0-3.3V)
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz - Band: 2400 (MHz)
- Wi-Fi Direct (P2p), Soft Access Point
- Integrated TCP / IP stack
- PLL, regulators and power management units Integrated

A Mini WIFI board ESP8266 contains 16MB flash, external antenna connector and built-in ceramic antenna based on ESP-8266EX. Wemos D1 Mini Pro-16 Module + Esp8266 Wifi Series Wireless Antenna features:
- Compatible with Arduino, programming with the Arduino IDE, MicroPython, NodeMCU
- Supply voltage: 5V
- Logical levels: 3.3V - 16MB (128Mbit) flash
- 11 pins of input / output - I2C / one-wire interface, LOLIN I2C port
- 1 ADC (input: 0-3.2V) - built-in ceramic antenna - external antenna connector - Power switch - Includes external WIFI antenna with IPEX SMA adapter Wemos D1 Mini Pro-16 Module + Esp8266 Wifi Series Wireless Antenna features:
of esp8266:
- Supported protocols: 802.11 b / g / n
- Network support: 2 , 4 GHz

ESP32 processor development board with WiFi and Bluetooth (BLE) compatible with Arduino Uno shields. It is much faster than the ESP8266 processor (NodeMCU and the like) . Wemos D1 ESP32 R32 WROOM-32 WiFi and Bluetooth features:
Power: 5-12VDC WiFi 802.11 b / g / n / e / i (802.11n up to 150 Mbps) Bluetooth v4.2 BR / EDR and BLE. Compatible with Arduino Uno shields. 6 Analog input. 20 digital inputs / outputs (3.3V) (with PWM functions, interrupt). UART, SPI, I2C communication. Size: 68Ã — 53 mm Micro USB connection. 4Mbytes Flash Memory 520Kb Clock: 240Mhz (a core dedicated to WiFi processing) Temperature: -40C + 85C Current: 250mA (max) Current in saving mode: 0.15mA Operating current: 20mA (without WiFi) Useful links for Arduino / Raspberry programming and projects with Arduino /

You can easily control any device over the Internet through your phone, computer, etc.
The module can handle 5 users at the same time, it can work in two modes: STA (client) and AP (access point).
In AP mode, the module is connected via WIFI directly to your phone or computer (in open field can be up to 300 meters).
In STA mode, the relay module is connected to the access point (router) that supplies the network.
Wi-Fi in the room where the relays are located. In this case, the range mainly depends on the power of the access point antennas (routers).
You should not turn off after the configuration is completed, as some of the parameters of the WIFI module cannot be saved when power is cut off.

Allows control: - Up to 2 bidirectional current motors
- Or 1 stepper motor Shield is compatible with NodeMcu ESP8266 CP2102 WIFI Development Board ESP8266 WiFi Motor Drive L293D Expansion Shield Board ESP12E NodeMcu features:
- Minimum operating voltage: 4.5 V
- Maximum operating voltage: 36 V
- Maximum current: ± 1.2 A
- Logic voltage: - 2.3V <= HIV <= VIN (high)
                        - 0.3V <= VIL <= 1.5V (low)
- Controller L293D
- Measures: 58x42 mm ESP12 port control kit: - D1, D3 - motorA
- D2, D4 - motorB

The adaptor for the well-known ESP-12 and ESP-12E module

The ESP32-CAM is a camera module with the ESP32-S chip. It features an OV2640 camera, several GPIOs to connect peripherals, and microSD card slot.

NodeMcu module based on ESP8266 controller and programming in Lua language. 
NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC. ESP8266-12E is an improved version of ESP8266-12. 
It works as a standard WiFi 802.11 b / g / n 2.4 GHz. 
USB communication - the CP2102 chip. Characteristic of ESP 12E: 
- Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V), 
- Supported protocols: 802.11 b / g / n, 
- Network support: 2.4 GHz, 
- Band: 2400 (MHz), 
- Wi-Fi Direct (P2p), Soft Access Point, 
- TCP Stack / Integrated IP, 
- PLLs, Regulators and Integrated Power Management Units, 
- Output Power: 0.15 (W); + 19.5dBm in 802.11b mode,

NodeMcu module based on ESP8266 controller and programming in Lua language
NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC
ESP8266-12E is an improved version of ESP8266-12
It works as a standard WiFi 802.11 b / g / n 2.4 GHz
USB Communication - CP2102 Chip
Characteristic:
ESP 12E ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi features:

- Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz
- Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point
- Integrated TCP / IP stack
- PLL, regulators and integrated power management units
- Output power: 0 , 15 (W); + 19.5dBm in 802.11b mode

USB adapter that allows a direct USB connection to your ESP8266 ESP-01 or ESP-01S WiFi module. Based on the CH340 integrated circuit, which is a USB - Serial converter (UART).

ESP32-S3-DevKitC-1-N8 general-purpose development board based on the ESP32-S3-WROOM-1 chip.

TinyS3 is the latest in Unexpected Maker's popular range of "Tiny" development boards. It's packed with amazing features and peripherals, wireless connectivity, and stacks of Flash and PSRAM, all in the same tiny package size as the original TinyPICO!

TUYA IoT interface module - you will be able to control your projects IoT Internet of Things interface of your Arduino. Tuya interface that allows you to control outputs of the Arduino module via WiFi network using apps for Android and iOS mobile devices. The device communicates with Arduino via UART interface, powered by 5V.

SparkFun IoT RedBoard development board compatible with Arduino. It incorporates an ESP32 chip with a 32-bit dual-core Xtensa LX6 microprocessor with a clock frequency of up to 240 MHz. It enables WiFi and Bluetooth wireless communication, making it versatile for Smart Home and IoT projects.

ESP32-WROOM-32E (ESP32-DEVKITC-32E) is an evaluation board with ESP32 processor, 4MB FLASH, 802.11 a/b/g/n (Wi-Fi, WiFi, WLAN) and BlueTooth® Smart Ready 4.x dual-mode. It is much faster than the ESP8266 processor (NodeMCU and similar), and very easy to use.

Useful adapter for 30-pin esp32 modules (2x15 pins). Provides easy and secure connections. You can use the terminal block sockets or create connections via female pin header.

Shelly 1 is a universal smarthome relay enabled to work with all the key smart home systems, including Google Home and Amazon Alexa, as well as an original Shelly solution Shelly Cloud

Classic development board designed and manufactured by Heltec Automation (TM), based on the ESP32-S3FN8 + SX1262. Integrates Wi-Fi, Bluetooth, lithium battery management system, dot matrix OLED screen, USB-C interface. Compatible with Arduino IDE, Micro Python, Platform.io, Espressif IDE. Our module is supplied with Lora antenna and IPEX adapter (U.FL) and header pins.

"SenseCAP K1100 - The Sensor Prototype Kit with LoRa® and AI allows you to quickly digitise your world with LoRaWAN® and solve real-world challenges. With this plug-and-play toolkit, anyone can add artificial intelligence to their edge devices and unlock the potential of AIoT.

Grove - Vision AI module with Himax HX6537-A processor, thumb-sized AI-powered OV2640 camera sensor, compatible with YOLO v5 and Edge Impulse.