MH-Z19C Infrared Sensor module 5000ppm CO2 monitor HVAC PWM output UART CO2 sensor model MH-Z19C. High precision working voltage 5.0±0.1V DC. The measuring range is between 0 and 5000 ppm. It has a low power consumption. UART and PWM output. Code S0044 Backorder Price €29.49
EMG Muscle Signal Sensor Signal Electromyography EMG Muscle Signal Sensor Signal Electromyography features: EMG Muscle signal sensor module kit with 6 disposable electrodes The EMG sensor serves as a bridge to detect small electrical pulses product of muscle activity and transform them into a signal recognizable by Arduino. NOTE: DO NOT USE THIS SENSOR FOR MEDICAL PURPOSES. Code Examples: https: //github.com/AdvancerTechnologies/MuscleSensorV3 Code M0116 Last items in stock Price €36.90
BMP280 Temperature Barometric Pressure Sensor Module/SPI This module includes the BMP280 component that converts atmospheric pressure, temperature and humidity with high precision into a digital signal.The equipment uses the two I2C and SPI interfaces. The very good measurements made by the BMP280 allows the module to be used as an altimeter.Its 5-pin straight connector allows easy connection to other electronic boards. BMP280 Temperature Barometric Pressure Sensor Module/SPI features: - Interfaces: -I2C (up to 3.4 MHz) -SPI (up to 10 MHz)- Supply voltage: 1.8-5VDC- Module operating range: - Temperature: -40ºC to + 85ºC0-100% - Pressure: 300-1100 hPa- Resolution of the measures: - Temperature: 0.01ºC Code M0134 Available Regular price €4.99 -€1.00 Price €3.99
Dust Sensor Module PPD42NS PM2.5 This module is a dust sensor capable of detecting more than one micron of dust particles. It has two types of output: output of 4V high-level signal for a clean environment and 0.7V low-level signal for a particle-laden environment. Its power supply is 5VDC and the particle detection range is maximum at 8000 units per 283ml. Dust Sensor Module PPD42NS PM2.5 features: - Supply voltage: 5VDC - Working current: 90mA - Sensitivity: 0.5V / ( 0.1 mg / m3) - Particle detection minimum value: 1 micron - Output mode: Hi = 4V impulses (clean environment); Lo = 0.7V (charged environment) - Temperature working: 0-45 ° C - Working humidity: 0-90% RH - PCB size: 59x45x22 mm Code S0123 Available Regular price €11.89 -€2.00 Price €9.89
LDR Module Motor Resistance KY-018 This module adapted for the arduino is a light sensor. The resistance of the LDR cell decreases as the light intensity increases. On the contrary in a dark environment, the resistance of the LDR cell increases accordingly. Characteristic: - 3-pin connector: 1- GND 2- VCC 3- analog output - the voltage depending on the light - Supply voltage: 3.3 V-5VDC - PCB size: 19x15x8 mm Code S0122 Available Price €1.39
BME280 Digital Temperature Humidity Barometric Pressure Module This module includes the component BME280 that is translated into a digital signal.The equipment uses the two I2C and SPI interfaces. The BME280 does not allow the module to be used as an altimeter as opposed to its successor BMP280.Its 5-pin straight connector allows easy connection to other electronic boards. BME280 Digital Temperature Humidity Barometric Pressure Module features: - Interfaces:- I2C (up to 3.4 MHz)- SPI (up to 10 MHz)- Supply voltage: 1.8-5VDC- Module operating range:- Temperature: -40ºC to + 85ºC- Humidity: 0-100%- Pressure: 300-1100 hPa- Resolution of the measures:- Temperature: 0.01ºC- Humidity: 0.008%- Pressure: 0. 18Pa- Accuracy of the measures:- Temperature: +/> Code M0135 ✗ Out-of-Stock Regular price €14.95 -€5.00 Price €9.95
Digital Touch Sensor B21 The module is based on a touch sensitive IC capacitive touch switch module (TTP223B). In the normal state, the module produces Low power consumption. When a finger touches the corresponding position, the module output is high, if not touched for 12 seconds, it switches to low power mode. Digital Touch Sensor B21 features: - Low power consumption - Input voltage: 2 - 5.5VDC - Can replace the traditional touch of a button - Four M2 screws diameter 2.2 mm that position the holes for easy installation - 3-pin control interface: 1- GND 2- VCC 3- Control signal (output pin) - Power indicators: Bright green LED when the sensor is on Code M0130 Available Price €1.49
Unipolar Hall Effect Magnetic Sensor IC SH3144E Definition of the Hall effect: When a current passes through a bar of semiconductor (or conductive) material, and if an induction magnetic field B is applied perpendicularly to the direction of current flow, a voltage, called the Hall voltage, proportional to the magnetic field, and the current appears on the side faces of the bar. This voltage is proportional to the speed of movement of the charge carriers, It is considerably higher in semiconductor materials than in metal conductors. Magnetic Sensor Characteristic: - Input Voltage: 3.8-30VDC - Output current: 40mA High output current capacity -40 mA maximum absolute Quad-Hall design virtually eliminates static mechanical effects Magnetic compensated temperature - Digital current sinking output Code S0049 Available Regular price €0.90 -€0.25 Price €0.65
Hall Effect Sensor Module KY-003 with SH3144E TO-92 This module adapted for the arduino is a unipolar Ic Hall effect magnetic sensor. The Hall effect is when a current passes through a bar of semiconductor (or conductive) material, and if an induction magnetic field B is applied perpendicular to the direction of current flow, a voltage, called Hall voltage, proportional to the magnetic field, and the current appears on the faces sides of the bar. This tension is proportional to the displacement speed of the charge carriers, which is considerably higher in semiconductor materials than in metal conductors. Hall Effect Sensor Module KY-003 with SH3144E TO-92 features: - 3-pin connector: 1- GND 2- VCC 3- Voltage is recovered depending on the magnetic effect - Supply voltage: 5VDC - Output current: 40mA Code M0131 Available Price €1.69
PMS5003 High Accuracy Particle Concentration Sensor The sensors can be integrated into a variety of instruments associated with a concentration of airborne particles to improve equipment, provide timely concentration, and have Exact data. Present the laser that scatters products on airborne particles, at the same time at a specific angle collect scattered light, changing the intensity curve that scatters over time. The microprocessor uses the algorithm based on the MIE theory to deduce the grain size contained in the air and the concentration of the particles per unit and quantity. Characteristic: - Power supply: 4.5-5.5 VDC - Measurement range: 0.3-1.0ï¼ ›1.0-2.5ï¼› 2.5-10 µm (micrometer) - Accuracy of count: 50%@> Code S0046 Available Price €27.90
Ultrasound Distance Sensor HC-SR05 Ultrasonic sensors overcome many of the weaknesses of IR sensors by providing distance measurement regardless of the color and illumination of obstacles. Ultrasound Distance Sensor HC-SR05 features:- Power supply: 4.5-5.5 VDC - Supply current: 10 to 40 mA - Activation pin format: 10 μs digital pulse - Echo Pin Output: 0-Vcc - Echo Pin Format: the output is DIGITAL and directly proportional with range. See our conversion formula below - Measurement range: 2cm to ~ 4.5m - Measurement resolution: 0.3cm - Measurement angle: up to 15 degrees - Measurement speed: 40 Hz, - Connector: standard 5-pin male connector that can be connected directly to boards or breadboards: - 1: VCC - 2: Trig - 3: Echo Code S0047 Available Price €1.95
MAX9812L Amplified Microphone for Measuring Sound The MAX9812 is a sound amplifier specially designed to treat the signal coming from microphones.We can use it together with Arduino to measure sound from a processor like Arduino.When we saw the modules with microphone we commented that, in general, the signal generated is too low to be registered correctly.If we want to be able to measure sounds, we will have to amplify the signal. The MAX9812L has single / dual inputs, fixed gain of 20dB, bandwidth of 400 kHz, low noise and low signal distortion 0.015% THD.There are two models, its supply voltage is 2.7V to 3.6V.We can use the sensors with MAX9812 for applications that require measuring the intensity or frequency of the sound. Code M0151 ✗ Out-of-Stock Price €6.90
Color Recognition Sensor GY-31 TCS230 TCS3200 It consists of three principles of induction of primary colors, if you know the composition of all types of color values, you can know the color of the test object.For TCS230, a color filter is chosen, only a certain primary pass is allowed, it is stopped by another color. For example, when choosing a red filter, the incident light can only be stopped in red, blue and green, so you can get the intensity of the red beam of light.For the same reason, the choice of other filters, can obtain the intensity of blue light and green light.Through these three values, the color of the light can be projected onto a TCS230 sensor. Color Recognition Sensor GY-31 TCS230 TCS3200 features: - Operating voltage: 3 - 5 VDC- Model GY-91- Chip TCS230 TCS3200 Code M0152 Available Price €9.95
Digital Light Intensity Sensor with Photo Resistance with LM393 Controller This photo-resistance module is very sensitive to ambient light. Activation of the microcontroller or retransmission modules,The brightness module of the ambient light reach the set threshold, the output is high when the ambient light exceeds the set threshold.The DO output can be connected directly to a microcontroller to detect the light environment and create a light control switch.It has a speed range of 0% to 100%. Digital Light Intensity Sensor with Photo Resistance with LM393 Controller features: - Operating voltage: 3.3 - 5 V- Input current: 50 mA- Use a very sensitive photo resistance- Use a LM393 wide voltage comparator, high quality output signal- Adjustable potentiometer can regulate the brightness of detected light Code M0156 Available Price €1.69
Dallas Temperature Sensor Module DS18B20 The DS18B20 is a digital temperature sensor from Dallas Semi Conductors, used to measure ambient temperature or to carry out tests. It supports multipoint readings of the mesh networking type, being able to be deployed in three lines, in order to achieve these readings, it has a built-in pull-up resistance. Dallas Temperature Sensor Module DS18B20 features: - Operating voltage: 3 - 5.5 VDC - Measurement operating temperature: -55 ° C - 125 ° C - Output current: 5 μA - Accuracy of ± 0.5 ° C between -10 ° C and + 85 ° C - Storage temperature: -55 ° C - + 125 ° C - 100% new and high quality - Module DS18B20 temperature measurement sensor - The DS18B20 sensor has a pull-up resistor - Power indicator LED on the module Code S0124 Available Price €1.95
GY-91 10DOF 4 Sensors in 1 Module with MPU-9250 and BMP280 This small 10-DOF sensor module GY-91 is more compact than the GY-80 module.The module uses a unique MPU-9250 chip combination with built-in 3-axis gyroscope, 3-axis accelerometer, digital compass and BMP280 enhanced barometric pressure sensor.The MPU-9250, delivered in a 3x3x1mm QFN package, is the smallest 9-axis MotionTracking device in the world and incorporates the latest InvenSense design innovations, allowing dramatically reduced chip size and power consumption, while improving the performance and the cost. Enhancements include low-power accelerometer mode support with only 6.4μA of and provides improved 16-bit compass data resolution (0.15 μT per LSB). Code M0079 Available Price €15.95
M12 Inductive Proximity Sensor NPN DC 6-36V LJ12A3-4-Z/BX 3D Printer M12 Inductive Proximity Sensor NPN DC 6-36V LJ12A3-4-Z/BX 3D Printer features: - This sensor can be configured as Z axis auto level - Inductive proximity sensor detection switch LJ12A3-4-Z / BX - NPN DC6-36V - Often used for 3D printer bed leveling - Typical application: 3D printer bed level sensor - Type of Cylindrical DC cable 3 type of cable (black, brown, blue) - Inductive sensor type - NPN NO (Normal Open) - Detecting Distance 4mm - DC supply voltage 6-36V - 300mA current output - 0.5KHz response frequency - Detects iron / aluminum - Operating temperature -25 ° C to + 55 ° C (Condition non-freezing) - Head diameter 12 mm - Size 6.2 x 2cm - Cable length 100cm Code S0125 Available Price €3.49
Digital Thermometer with External Temperature Probe - Immerse the probe in the fish tank to measure the water temperature Digital Thermometer with External Temperature Probe features: - Cable length: 1m- LCD screen- Temperature range: -50 C ~ + 70C- Powered by 2 batteries x LR44 / AG13 button (included)- Cable length: approx.100cm- External Dimensions: 48 x 28.5 x 15.2 mm- Dimension LCD screen: 35 x 16 mm- Color: Black- Used to measure the temperature in: the rooms, the aquarium, terrarium in the heating system, in the car, fridge, freezer Code S0039 Available Price €2.79
DS18B20 Digital Temperature Sensor Probe 10m Encapsulated with water resistant stainless steel with sensor dimensions 5,5 * 50mm, cable length 10m. DS18B20 Digital Temperature Sensor Probe 10m features:- Based on the DS18B20 chip- Supply voltage: 3 ~ 5.5V- Consumption <5mA- Measuring Range: -55 °C to 125 °C- Accuracy: +/- 0,5ºC- Outputs: - GND black - Vcc red - Yellow digital output- Inocidable steel- Cable length: 10m Code S0127 Available Price €14.99
Ceramic Piezoelectric Disc 35mm with Mika PVC 49mm Characteristic: - Diameter: 35mm - Frequency: 2.3 kHz - Impedance (resonance): 300 Ohm - Capacity (at 1kHz): 25,000 pF - Dimensions: 35x0.50mm Code M0167 Available Price €0.49
Piezoelectric Vibration Sensor for Arduino UNO When the piezoelectric ceramic shock will generate an electrical signal, the analog port of the Arduino controller may perceive weak vibration signals. Can also be done with jobs related to vibration interactions, such as electronic drums. Code M0168 Available Price €2.49
Speed sensor module for Arduino motors Speed sensor module for Arduino motors features: - Slot-type optocoupler sensor, slot width: 10 mm. - The encoder module is a device that can help you in the creation of your robotics and automation project, whether you want to know the speed of a motor or the exact position of it. - Output Out - Emits a low level when there is no block in the slot, otherwise it produces a high level. The operating mode: - When the sensor is blocked the OUT output is high - Power supply: 3.3-5V - Current consumption 15 mA max. - PCB dimensions: 25 x 20 mm Code S0129 Available Price €1.88
Inductive proximity sensor PL-05N 5mm with NPN output Inductive Proximity Sensor PL-05N NPN Limit Switch is used for controlling machinery as part of a control system, as a safety interlock, or to count objects passing a point. Inductive proximity sensor PL-05N 5mm with NPN output features: - Manufacturer: Fotek,- Square Type,- Sensing distance: 5mm,- Operating voltage: 10 - 30 VDC,- Response frequency: 800Hz,- Output method: NPN, 150mA load,- Hysteresis: <10% of sensing distance,- Protection degree: IP67,- Working temperature/Hum: -20ºC - +80ºC, 35% - 90% RH,- Body dimension: 30.5x17.9x10.2mm (LxWxH),- Mounting Method: Flush,- Sensing Direction: Horizontal,- Materia Housing: High-impact plastic,- Screw hole: 3.2mm, Pitch: 10.5mm, Code S0130 Available Price €11.90
Inductive proximity sensor PL-05P 5mm with PNP output Inductive Proximity Sensor PL-05P PNP Limit Switch is used for controlling machinery as part of a control system, as a safety interlock, or to count objects passing a point. Inductive proximity sensor PL-05P 5mm with PNP output features: - Manufacturer: Fotek,- Square Type,- Sensing distance: 5mm,- Operating voltage: 10 - 30 VDC,- Response frequency: 800Hz,- Output method: PNP, 150mA load,- Hysteresis: <10% of sensing distance,- Protection degree: IP67,- Working temperature/Hum: -20ºC - +80ºC, 35% - 90% RH,- Body dimension: 30.5x17.9x10.2mm (LxWxH),- Mounting Method: Flush,- Sensing Direction: Horizontal,- Materia Housing: High-impact plastic,- Screw hole: 3.2mm, Pitch: 10.5mm, Code S0131 Last items in stock Price €10.95
Infrared LED Flame Sensor 5mm Led infrared sensor.Detector of the source of fire or flame, can detect a flame or wavelength 760 nm-1100 nmParticularly sensitive to the flame spectrum.This optical flame sensor is a device that detects the existence of combustion by the light emitted by it. Infrared LED Flame Sensor 5mm features: - Range of light, Distance of 80 cm.- Angle detection of about 60 degrees,- This light can be detected by an optical sensor,- Can be captured by digital inputs and analog inputs of Arduino. Code S0132 Available Price €0.45
Infrared LED Flame Sensor 5mm module Led module infrared sensor for ArduinoDetector of the source of fire or flame, can detect a flame or wavelength 760 nm-1100 nmParticularly sensitive to the flame spectrum.This optical flame sensor is a device that detects the existence of combustion by the light emitted by it. Infrared LED Flame Sensor 5mm module features:- 4 Pins Output: - A0: analog output - D0: digital output - GND: ground connection - VCC: 5V module power- Range of light, Distance of 80 cm.- Angle detection of about 60 degrees,- This light can be detected by an optical sensor,- Can be captured by digital inputs and analog inputs of Arduino. Code S0133 Available Price €1.39
Black UV sensor module UVM-30 for Arduino UVM-30A sensor module suitable for any location and requires stable and precise measurement of UV light. Ideal for Arduino projects. Black UV sensor module UVM-30 for Arduino features: - Operating voltage: 3-5 VDC, - Voltage input: DC 0-1 VDC, - 3-pin connector: - GND (-): ground connection, - Out: sensor output signal, - VCC (+): sensor supply, - Measurement accuracy: +/- 1UV index, - Working current: 0.06mA (standard) / 0.1mA (max.), - Response wavelength: 200-370 nm, - Working temperature: -20ºC - + 85ºC, - PCB size: 28x12mm. Code M0178 Available Price €9.95
DS18B20 Digital Temperature Sensor Probe 5m Encapsulated with water resistant stainless steel with sensor dimensions 5,5 * 50mm, cable length 5m. DS18B20 Digital Temperature Sensor Probe 5m features:- Based on the DS18B20 chip- Supply voltage: 3 ~ 5.5V- Consumption <5mA- Measuring Range: -55 °C to 125 °C- Accuracy: +/- 0,5ºC- Outputs: - GND black - Vcc red - Yellow digital output- Inocidable steel- Cable length: 5m Code S0134 Available Price €7.95
Circular force sensing resistor The resistance of the sensor has a force measurement range of 0-10 kgIts resistance varies depending on how much pressure is applied to the detection area, the greater the force, the lower the resistance.Peel and stick the rubber backing on the other side of the detection area to mount.It can detect the applied force in the detection area in the range of 0g-10kg. Circular force sensing resistor features: - Detection area: 1.27cm / 0.5 inches- Output signal: passive variable resistance- Force detection range: 0 g ~ 10 kg- Length: 6 cm / 2.36 inches- Width: 1.9cm / 0.75 inches Code S0135 Available Price €8.49
Heartbeat sensor for Arduino This detection module combines a phototransistor and an LED that, when placed on a finger or ear lobe, provides a reading.By reading this signal you can interpret a change in the signal as a heartbeat.Keep in mind that this is a sensitive module and you will experience the noise from home lights and other sources, since minimizing the lighting of the unit will help get the readings. Heartbeat sensor Arduino features: - Connection pins:- S: Analog output- (+): Power supply 3-5 VDC,- (-): GND.- Length: 18mm,- Width: 18mm,- Height: 4mm,- Operating temperature: -40ºC to + 85ºC. Code S0136 Available Regular price €9.49 -€1.50 Price €7.99
UV detection module for Arduino UV 200-370nm DC 3.3-5V 0.1mA Ultraviolet ray detection module 200-370nm with a supply voltage of 3.3-5 VDC and a very low consumption of 0.1mA. 100% compatible UNO module. Characteristic: - Operating voltage: 3.3-5 VDC - Output voltage: 0-1 VDC - 3-pin connector: - OUT: output signal - VCC: Supply voltage - GND: Ground connection - Test accuracy: ± 1UV INDEX - Current: 0.06mA (typical), 0.1mA (maximum) - Wavelength of the response: 200nm-370nm (ultraviolet rays) - Response time: less than 0.5 seconds - Operating temperature: -20ºC - + 85ºC - Size: 19.80 x 15mm Code M0188 ✗ Out-of-Stock Price €6.90
TCRT5000 Module 3.5cm IR infrared sensor The optical (reflective) module sensor with LM393 comparator, which detects obstacles with high accuracy. The ideal detector for obstacle detection for the installation of intelligent robots.TCRT5000: reflective optical sensor that has a compact construction where the light emitter and receiver are placed in the same direction to detect the presence of an object using infrared reflection on the object. The transmitter is an infrared LED and the receiver is a phototransistor. The sensor allows the detection of an object at a distance of up to 3.5 cm from the white paper and 1 cm from the person's finger. Code S0138 Available Price €1.69
Holder for HC-SR04 Ultrasonic Sensor Holder for ultrasonic, distance meter HC-SR04. Ideal for installing the sensor on mobile platforms such as robots, vehicles, etc. Code S0137 Available Price €0.99
Sensor SCT-013-030, Non-Invasive 30A AC Current Meter The sensor measures the current flowing in the cable without cutting it. The measurement is made on a single insulated wire, the output is an analog voltage from 0 to 1 V. Sensor SCT-013-030, Non-Invasive 30A AC Current Meter features: Input current: 0 to 30A AC Output voltage: 0 to 1 V AC Built-in load resistance: 62 Ω Winding ratio: 1800: 1 Operating temperature range: -25 ° C to 70 ° C Cable length: 1 m Sensor weight: approximately 45 g Sensor SCT013-030 datasheet Code M0203 Available Price €6.49
SparkFun Triple Axis Accelerometer Breakout - MMA8452Q (with Headers) Sensor used for measuring of the object acceleration in 3 axis in the range of either ±2g, ±4g or ±8g. It is powered with 1.95V to 3.6V. What sets this module apart is its user-friendliness, compatible size and low power consumption. it comes with headers attached Code SP001 Available Price €16.99
SparkFun Triple Axis Accelerometer Breakout - ADXL335 This accelometer is powered with 1.8 to 3.6V and consumes only up to 320 uA of current. The circuit fits on the small 18mm on 18mm board and is fully compatible with Arudino Code SP002 Available Price €21.99
SparkFun Triple Axis Accelerometer Breakout - LIS331 This board features and extremely low power LIS331HH accelerometer. The unit is a MEMS three axis linear accelerometer with a I2C- SPI serial interface enabling use with embedded applications. The range of measurement includes three options +-6g/+-12g/+-24g and enables datalogging with output rates fro 0.5 Hz to 1kHz. Check this and plenty of other accelerometers in our offering of both Sparkfun and other producers Code SP003 Available Price €18.95
SparkFun Triple Axis Accelerometer Breakout - MMA8452Q (wo headers) Sensor used for measuring of the object acceleration in 3 axis in the range of either ±2g, ±4g or ±8g. It is powered with 1.95V to 3.6V. What sets this module apart is its user-friendliness, compatible size and low power consumption. it comes with headers attached It is a version without headers of a popular BOB-09868 from SparkFun. In our offer, we have a versuib with headers (SP0001) and with QWIC system (SP0005). Code SP004 Last items in stock Price €16.99
SparkFun Triple Axis Accelerometer Breakout - MMA8452Q (Qwiic) Sensor used for measuring of the object acceleration in 3 axis in the range of either ±2g, ±4g or ±8g. It is powered with 1.95V to 3.6V. What sets this module apart is its user-friendliness, compatible size and low power consumption. It comes with QWIIC connectors Code SP005 Last items in stock Price €14.99
SparkFun Pulse Oximeter and Heart Rate Sensor - MAX30101 & MAX32664 (Qwiic) This tiny little board features two chips from Maxim Integrated: MAX32664 and MAX30101. The 30101 Oximetry module is the sensor on board responding for both oximetry and heart rate sesnsing. The MAX32664 is equipped with a Cortex M4 handling algorithimc calculations, digital filtering and automatic gain control. The board comes with I2C and SparkFun has provided to it Qwiic connectors for ease of use. Code SP030 Last items in stock Price €52.99
Sensor: photoelectric E3Z-T61A 2M OMRON Photoelectric sensor standard, reliable assurance of 1 million units per year. · Industry's top class built-in amplifier · Guaranteed low-temperature operation that can be used in freezing warehouse · Improvement of coincidence between optical and mechanical axis. · Protection of sensor even if wiring mistake occurs output reverse protection function is carried (we add diode for reverse connection protection to output line). Code S0139 Available Price €85.00
Plastic Water Solenoid Valve - 12V - 1 / 2 ″ Nominal 12VDC plastic solenoid valve. Normally closed. Liquid can flow in one direction and a minimum pressure of 0.02Mpa (3 PSI) is required. This liquid valve would be a great addition to your robotic gardening project. There are two 1/2 ″ outlets. Normally, the valve is closed. When 12VDC is applied to the two terminals, the valve can be opened and pushed. Code M0210 Available Regular price €7.95 -€1.00 Price €6.95
F50-12V 10W DC Micro Hydro Generator Mini electricity generator, built base on a turbine and an electric generator that converts kinetic energy into electricity. The generator output is rectified and regulated for a maximum of 12V. Please note -if we want to generate more current, the turbine will oppose the greater resistance to the flow of water, and the voltage may drop if the water flow is not sufficient. This generator is made of plastic and the turbine is totally isolated from the generator and rectifier, the outputs are 1/2 "usually found in domestic pipes. Code M0211 Last items in stock Regular price €11.95 -€1.50 Price €10.45
High Precision i2c Digital Current Sensor Module GY-INA219 GY-219 The INA219 breakout board can be powered by the 5V or 3V pin on your Arduino and communicates via I2C. If you want to sense an Direct Current (DC) with high accuracy and voltage too, we suggest you to use this sensor. I2C sensor can easily interfaced with arduino. It uses 4 pins only. Code M0212 Available Price €3.39
HX711 Modulo Conversor + Celda de Carga 1kg Load Cell Conversor A/D 24bits M0119 The module uses a 24-bit high precision A / D conversion chip HX711.The input circuit can be configured to provide a bridge.The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. Module features: - Two selectable differential input channels- Active low noise PGA with selectable gain of 32, 64 and 128- Power supply regulator for load cell and ADC analog power supply- Oscillator on chip that does not require external component with optional external glass- Power-on-reset on the chip- Simple serial control and serial interface: controls driven by pins, programming is not required- Output data rate 10SPS or 80SPS selectable Code M0119 Available Regular price €5.78 -€0.95 Price €4.83
HX711 Modulo Conversor + Celda de Carga 2kg Load Cell Conversor A/D 24bits The module uses a 24-bit high precision A / D conversion chip HX711.The input circuit can be configured to provide a bridge.The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. Module features: - Two selectable differential input channels- Active low noise PGA with selectable gain of 32, 64 and 128- Power supply regulator for load cell and ADC analog power supply- Oscillator on chip that does not require external component with optional external glass- Power-on-reset on the chip- Simple serial control and serial interface: controls driven by pins, programming is not required- Output data rate 10SPS or 80SPS selectable Code M0120 Available Regular price €5.78 -€0.95 Price €4.83
HX711 Modulo Conversor + Celda de Carga 5kg Load Cell Conversor A/D 24bits The module uses a 24-bit high precision A / D conversion chip HX711.The input circuit can be configured to provide a bridge.The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. Module features: - Two selectable differential input channels- Active low noise PGA with selectable gain of 32, 64 and 128- Power supply regulator for load cell and ADC analog power supply- Oscillator on chip that does not require external component with optional external glass- Power-on-reset on the chip- Simple serial control and serial interface: controls driven by pins, programming is not required- Output data rate 10SPS or 80SPS selectable Code M0121 Last items in stock Regular price €5.78 -€0.95 Price €4.83
HX711 Modulo Conversor + Celda de Carga 10kg Load Cell Conversor A/D 24bits The module uses a 24-bit high precision A / D conversion chip HX711.The input circuit can be configured to provide a bridge.The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. Module features: - Two selectable differential input channels- Active low noise PGA with selectable gain of 32, 64 and 128- Power supply regulator for load cell and ADC analog power supply- Oscillator on chip that does not require external component with optional external glass- Power-on-reset on the chip- Simple serial control and serial interface: controls driven by pins, programming is not required- Output data rate 10SPS or 80SPS selectable Code M0122 Available Regular price €6.28 -€1.45 Price €4.83
HX711 Modulo Conversor + Celda de Carga 20kg Load Cell Conversor A/D 24bits The module uses a 24-bit high precision A / D conversion chip HX711.The input circuit can be configured to provide a bridge.The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. Module features: - Two selectable differential input channels- Active low noise PGA with selectable gain of 32, 64 and 128- Power supply regulator for load cell and ADC analog power supply- Oscillator on chip that does not require external component with optional external glass- Power-on-reset on the chip- Simple serial control and serial interface: controls driven by pins, programming is not required- Output data rate 10SPS or 80SPS selectable Code M0123 Available Regular price €5.98 -€1.15 Price €4.83
Kit Seeed Grove 20 sensors for Arduino The kit includes 20 basic sensors, which will help you to easily kick-start any project. The sensors are featured with a proprietary Seeed Grove connectors enabling easy connection without soldering and a comprehensive guide book with exemplary classes. Code SS001 Last items in stock Price €67.95
Kit Seeed Grove 30 sensors for Arduino The kit includes 30 basic sensors, which will help you to easily kick-start any project. The sensors are featured with a proprietary Seeed Grove connectors enabling easy connection without soldering and a comprehensive guide book with exemplary classes. Code SS002 Last items in stock Price €95.59
Kit Seeed Grove 40 sensors for Arduino The kit includes 40 basic sensors, which will help you to easily kick-start any project. The sensors are featured with a proprietary Seeed Grove connectors enabling easy connection without soldering and a comprehensive guide book with exemplary classes. Code SS003 Last items in stock Price €109.90
Kit Seeed Grove Arduino Starter Seeed Grove Arduino Starter kit is a game-changer for schools and robotic classes. You get a set of 10 sensors with a Arduino compatible board and 12 classes for only 28.99 EUR! Code SS004 Available Price €35.90
GY-MAX4466 MAX4466 Electret Microphone Adjustable Amplifier Module The module is equipped with an electret microphone with a sensitivity in the range of 20-20 kHz and the amplification is used in the Maxim MAX4466 integrated circuit, an operational amplifier specially designed for use as a microphone preamplifier. Code M0214 Available Regular price €5.95 -€1.00 Price €4.95
CJMCU-811 CCS811 Carbon monoxide VOC CO Digital air quality gas sensor The Carbon Monoxide sensor is a low-power digital gas sensor which has a CCS811 sensor and an 8-bit microcontroller, contains an analog-digital converter so that it can detect indoor air quality which can detect monoxide carbon (CO) and a wide range of volatile organic compounds (VOCs). It is a sensor designed to monitor air quality inside personal devices such as mobile devices and smart watches, with low power consumption that can be used with battery Code S0140 ✗ Out-of-Stock Price €17.95
Sensor SCT-013-050, Non-Invasive 50A AC Current Meter The sensor measures the current flowing in the cable without cutting it. The measurement is made on a single insulated wire, the output is an analog voltage from 0 to 1 V. Sensor SCT-013-050, Non-Invasive 50A AC Current Meter Code M0220 Available Price €6.95
Nova PM Sensor SDS011 - Air quality sensor - High precision laser PM2.5 Dust test module Air quality sensor with high precision whose SDS011 uses laser dispersion to detect particle concentration between 0.3 and 10 um in the air. With digital output by USB (UART) and built-in fan. It is a powerful sensor, fast (response less than 10s), accurate and reliable. Code S0142 Last items in stock Price €32.90
Fingerprint Readers JM-101 - optical sensor This fingerprint scanner (as608-optical reader) is ideal for Arduino or Raspberry thanks to its small size and low power consumption. It has a simple interface, high reliability, good adaptability of wet and dry fingers, fast recognition speed and also in fast fingerprint search. Storage capacity of up to 120 fingerprints in its internal FLASH memory. Code S0143 Available Price €14.49
Vertical Liquid Level Sensor Switch - 118mm Level sensor for liquids with float. The liquid level sensor acts as a switch. Liquid level float sensors are used when constant control and regulation of the liquid level (water, oil and other fluids) is required such as extraction pumps. The sensor is equipped with a float with a magnet which, acting by the buoyancy force of the fluid, moves along the tube, shortening or opening the reed switch. It can be used to detect liquid levels that are too high or too low. Ideal for all those applications where the level of non-corrosive liquids such as water tanks or aquariums needs to be monitored. It is made of stainless steel. Code S0141 Available Price €21.79
Magnetic sensor switch for windows/doors 14X27mm adhesive This sensor behaves like a switch that closes the circuit when both parts are put together. Ideal for intrusion detection, alarm system, light control and opening and closing devices. Code K0275 Backorder Price €1.99